Baby BMW Forum banner
1 - 17 of 17 Posts

· Registered
Joined
·
55 Posts
Discussion Starter · #1 ·
Hello Guys,

I have recently sold my 1 series and no longer require the SSDD carbon spoiler I had on it, it is in mint condition only on the car for a few months, bought brand new from SSDD motorsport not long ago for £165 with receipt to prove, i'm now looking for £70 for it collected from Westbury Wiltshire.

Please see pics below, only marks are from minor glue residue on the bottom of the spoiler from where it was on the car previously.









 

· Registered
Joined
·
672 Posts
If it fits my e88 I'll take it pal
 

· Registered
Joined
·
672 Posts
Nimrod said:
If it fits my e88 I'll take it pal
I've got an SSDD on my e88... Needed help keeping it in position while it bonded but all fits fine..

Bargain too.. well worth snapping this up :)
What glue is needed pal?
Also what do you mean when you say help needed keeping it down?
 

· Registered
Joined
·
521 Posts
just wonder what the original paintwork was like when you removed the spoiler, clean up okay ? also you any pics with the car when it had the spoiler fitted ?
 

· Registered
Joined
·
55 Posts
Discussion Starter · #9 ·
Paintwork was fine just use some meguaires detailing spray to get the residue off, unfortunately the only picture I got on my phone is that one above on the car, will look through my hard drive later to see if I can find any more!
 

· Registered
Joined
·
672 Posts
james button said:
I used plastic G clamps to hold it over night while the bond set, cannot remember the glue I used though unfortunately!
Ok perfect mate. Well as said if you can post dibs and I'll take it
 

· Registered
Joined
·
521 Posts
james button said:
Paintwork was fine just use some meguaires detailing spray to get the residue off, unfortunately the only picture I got on my phone is that one above on the car, will look through my hard drive later to see if I can find any more!
okay thanks for the info and " Beasted " looks like you got yourself a nice bargain there mate we'll done :cool2:
 

· Registered
Joined
·
1,122 Posts
Beasted said:
james button said:
I used plastic G clamps to hold it over night while the bond set, cannot remember the glue I used though unfortunately!
Ok perfect mate. Well as said if you can post dibs and I'll take it
Now buddy when I fitted mine I used the 3m tape supplied been on 1 1/2 years now and never budged abit. Once I removed old and cleaned the boot ready I did a dry run 1st as y don't get much chance to try and move it once it's pressed on. Then I gently warmed to boot up with the missus hairdryer and it stuck like **** to a blanket lol
 

· Registered
Joined
·
672 Posts
Ian83w said:
Beasted said:
james button said:
I used plastic G clamps to hold it over night while the bond set, cannot remember the glue I used though unfortunately!
Ok perfect mate. Well as said if you can post dibs and I'll take it
Now buddy when I fitted mine I used the 3m tape supplied been on 1 1/2 years now and never budged abit. Once I removed old and cleaned the boot ready I did a dry run 1st as y don't get much chance to try and move it once it's pressed on. Then I gently warmed to boot up with the missus hairdryer and it stuck like sh*t to a blanket lol
Cheers Ian I will do a test fit first, and heat up and use 3m tape!
 
1 - 17 of 17 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top